Skip to content
EARTH LAYERS Send your finishes schedule
Home / Specify / Resin-bound surfacing / Addaset TP
Addaset resin bound aggregate paving along the promenade at Lusail Boulevard, Qatar
Resin-bound surfacing — technical data

Addaset TP

Polyurethane resin for tree pits

Manufacturer Addagrip Terraco Ltd
Country of origin United Kingdom
System family Resin-bound surfacing
Supplied and applied by Earth Layers by Conmarble

The product

A tree pit and light footpath resin. Laid at around 50 mm rather than the 18 to 22 mm of a surface course, so root zones stay porous and the surround stays walkable.

Where it is used

Tree pits Light use footpaths Porous surrounds where a deep build-up is needed

Substrates

Prepared and compacted sub-base to the landscape specification

Application data

Coverage, thickness, mix and cure, as declared by the manufacturer. Site conditions in the Gulf sit at the top of most of these ranges — allow for it in the programme.

Product Clear polyurethane resin, flexible and crack resistant
Density 1.05 g/cm³
Application temperature +5 °C to 30 °C
Surface temperature At least 3 °C above the dew point
Coverage 100 kg of 6–10 mm aggregate to 4–5 kg resin gives approximately 50 mm build-up per m²
Full chemical cure 7 days
Storage 3 months in original unopened containers

Performance data

Every figure below is reproduced from the manufacturer's own technical data sheet, with the test standard it was measured against. The sheet itself is in the download section.

PropertyResultStandard
Build-up Approx. 50 mm per m² at the stated mix ratio Addagrip data sheet
Aggregate size 6 – 10 mm Addagrip data sheet
Full chemical cure 7 days Addagrip data sheet

Where not to use it

The limits are as much a part of the specification as the performance. Everything here is stated on the manufacturer's data sheet.

Light use only — not a trafficked surface course Short shelf life: 3 months unopened Surface must be at least 3 °C above the dew point
Specification clause

Tree pit surfacing: Addagrip Addaset TP polyurethane resin bound 6–10 mm aggregate, laid approximately 50 mm thick at a minimum spread rate of 100 kg aggregate to 4–5 kg resin per m². Surface temperature to be at least 3 °C above dew point at the time of laying. 7 days full chemical cure.

Square brackets mark the choices that belong to the project. Send us the finishes schedule and we will return the clause completed, with the sample and mock-up programme against it.

Documents

Every document is the manufacturer's own, reproduced in full and unaltered under our cover. Free to download, no form.

Addaset TP TECHNICAL DATA SHEET · 3 pp · 1.1 MB
Download (PDF, 1.1 MB)

The rest of the

Addaset Resin bound surfacing Addaset ECO Resin bound surfacing with recycled aggregate Addaset Non UVR Resin bound surfacing, non-UV-stable Addacolor Coloured resin bound surfacing Addaflex R Resin bound rubber stone surfacing Addaflex R UV Resin bound rubber stone surfacing, UV-stable Stonebound UV Resin bound surfacing, UV-stable Stonebound Non UVR Resin bound surfacing, non-UV-stable Terrabase Resin bound surfacing, high permeability PU Addastone Resin bonded polyurethane surface dressing Addastone Thixotropic Agent Thickening filler

Technical support for the design team

We supply the material and we apply it, so the specification and the workmanship sit with one party. Send a finishes schedule, an elevation or a mood board and we will come back with the system, the build-up, the sample programme and a completed clause.

Send your finishes schedule Visit the showroom
Continue
Delivered projectsWhere this system is already installed.The specification hubEvery product, family and document in one place.Upload a scheduleSend a finishes schedule or bill of quantities for review.See it in personEvery range on real walls, by appointment.